1. Decide the shape of the book
✓ Trim size
Pick the trim size before you format anything: changing it later reflows every page. Novels are usually 5 × 8, 5.25 × 8 or 5.5 × 8.5 in; non-fiction is most often 6 × 9 in. Trims wider than 6.12 in or taller than 9 in count as large and cost more to print.
✓ Paper and page-count limits
A KDP paperback needs at least 24 pages (72 for standard color). The maximum depends on trim and paper: a 6 × 9 book can have up to 828 pages on white paper and 776 on cream. Cream paper is thicker, so the same book gets a wider spine.
✓ An even page count
Every sheet has two sides, so printed books always have an even number of pages, and KDP rounds an odd count up. Count everything: title page, copyright page, contents, blank pages and back matter. The final count sets your gutter and your spine width.
2. Page setup
✓ Margins and gutter for your final page count
The inside margin (gutter) grows with the page count, because thick books curve into the spine:
| Page count | Minimum inside margin |
|---|---|
| 24–150 pages | 0.375 in |
| 151–300 pages | 0.5 in |
| 301–500 pages | 0.625 in |
| 501–700 pages | 0.75 in |
| 701–828 pages | 0.875 in |
Outside, top and bottom margins must be at least 0.25 in, or 0.375 in with bleed. These are minimums; most well-made books use more. Page numbers and running heads must sit inside the margins too. Get the numbers for your book with the KDP margin calculator.
✓ Bleed, only if something prints to the edge
If any image or background runs off the edge of a page, the whole interior needs bleed: the PDF page becomes 0.125 in wider and 0.25 in taller, so 6 × 9 becomes 6.125 × 9.25 in. A text-only book doesn’t need bleed.
✓ The same page size on every page
Every page of the PDF must be exactly the trim size, or trim plus bleed. A stray page from another document, a landscape table page or a file exported at Letter size will be flagged.
3. Text and page numbers
✓ All fonts embedded
KDP asks for all fonts to be fully embedded in both the interior and the cover. Export a PDF with font embedding on; if you use an unusual font, check its license allows embedding.
✓ Nothing smaller than 7 pt
KDP’s legibility check wants all text at 7 pt or larger. Footnotes, captions, tables and the copyright page are where small text hides.
✓ Page numbers in order, even on the left
Page numbers must run in sequence, with even numbers on left-hand pages and odd numbers on right-hand pages. Roman numerals in the front matter are fine. Leave numbers and running heads off blank pages and chapter openings: that’s not a KDP rule, but it’s what readers expect from a printed book.
4. Images
✓ 300 DPI at the printed size
KDP recommends at least 300 DPI. What matters is pixels per inch on the page: a photo 1,200 pixels wide is 300 DPI printed 4 in wide, but only 200 DPI at 6 in. Enlarging a small image in Word doesn’t add detail.
✓ Transparency and layers flattened
When you create the PDF, make sure transparencies and layers are flattened, as KDP asks. Most “Save as PDF for print” presets do this; screen or web presets often don’t.
5. Blank pages
✓ No long runs of blank pages
KDP allows no more than 4 consecutive blank pages at the beginning or in the middle of the file, and no more than 10 at the end. Section breaks set to “odd page” can quietly add blank pages, so scroll through the whole PDF before uploading.
6. What readers notice
✓ Book typography, not word-processor typography
KDP won’t reject these, but reviewers and readers notice them:
- a single line of a paragraph stranded at the top or bottom of a page (widows and orphans);
- facing pages whose last lines don’t line up;
- wide gaps between words in justified text, or long runs of hyphenated lines;
- chapter openings that change style from chapter to chapter;
- front matter out of the usual order: title page, copyright page, dedication, then contents (often skipped in novels).
7. Cover
✓ Full wrap size, spine and barcode area
The print cover is one PDF: back cover, spine and front cover side by side, with 0.125 in bleed on every edge. The spine width is your page count times the paper thickness: 0.002252 in per page on white paper and 0.0025 in on cream, so a 300-page book on cream paper has a 0.75 in spine. Text on the spine is only allowed for books with more than 79 pages, and needs 0.0625 in of space on each side. Leave a 2 × 1.2 in area free on the back for the barcode KDP adds, unless you print your own. The spine width calculator gives the exact cover size and a template.
8. Before you click Publish
Before you upload, check the finished PDF with the free KDP PDF checker. It opens the file in your browser (nothing is uploaded) and shows the page size, fonts, blank pages, small text and margins that KDP may flag.
✓ Read every page in the Print Previewer
After you upload, KDP’s Print Previewer marks pages with problems: text in the margins, low-resolution images, a page size that doesn’t match. It’s free and catches most issues. A printed proof copy shows paper color, cover finish and how tight the gutter feels in your hands, but you pay for printing and shipping.
How BoundReady handles this
BoundReady, which we are building now, runs these checks automatically: it sets the margins and gutter for the final page count, sizes the spine and cover, and tests the files before you upload. Our own test book, a 346-page 6 × 9 paperback, passed KDP’s Print Previewer with no issues.